AudiWorld Forums

Search: Posts Made By: 80sGuy
Showing results 1 to 13 of 13
Search took 0.00 seconds.
Forum: A4 (B7 Platform) Discussion
04-01-2024, 03:13 PM
Replies: 11
Views: 487
Posted By 80sGuy

That sounds good. These sensors have a tendency...

That sounds good. These sensors have a tendency to go bad over the years due to heat, and when they do you'd often get intermittent problems and mediocre performance, making one think it isn't a big...
Forum: A4 (B7 Platform) Discussion
04-01-2024, 02:35 PM
Replies: 11
Views: 487
Posted By 80sGuy

Yes, it can be. There two sensors that can...

Yes, it can be. There two sensors that can trigger similar symptoms; the other is the Camshaft Position Sensor. But it can also be your coils or fouled up plugs. When's the last time you look under...
Forum: A4 (B7 Platform) Discussion
03-24-2024, 03:08 AM
Replies: 16
Views: 921
Posted By 80sGuy

Maybe it's time to replace that N75 'Wastegate'...

Maybe it's time to replace that N75 'Wastegate' valve (https://www.ecstuning.com/b-genuine-volkswagen-audi-parts/waste-gate-frequency-control-n75-valve/06f906283f/).
Forum: A4 (B7 Platform) Discussion
03-23-2024, 12:18 PM
Replies: 11
Views: 487
Posted By 80sGuy

Sounds like you need to replace your Crankshaft...

Sounds like you need to replace your Crankshaft Position Sensor.
Forum: A4 (B7 Platform) Discussion
03-22-2024, 11:49 AM
Replies: 8
Views: 354
Posted By 80sGuy

I've had episodes with my 2.0T not starting twice...

I've had episodes with my 2.0T not starting twice in 2023. Once in Jan and the last one on Nov. This happened when the engine was slightly warm or has been parked shortly and when I return to start...
Forum: 2.0T FSI Discussion
03-21-2024, 04:02 PM
Replies: 9
Views: 1,120
Posted By 80sGuy

Just replaced my Oil Filter Housing (original...

Just replaced my Oil Filter Housing (original Genuine Audi of course) and I just hand-tighten all the bolts on both filter housing and oil-cooler until they can no longer go, key is not forcing them...
Forum: A4 (B7 Platform) Discussion
03-14-2024, 02:37 AM
Replies: 8
Views: 1,554
Posted By 80sGuy

I know it's been a while but what have you done...

I know it's been a while but what have you done to rectify the issue? I thought I stripped that same darn bolt too (one on the top right). But I remained calm and sane and ended up removing the hard...
Forum: A4 (B7 Platform) Discussion
11-16-2023, 06:28 PM
Replies: 14
Views: 9,001
Posted By 80sGuy

Nice update. Thank you!

Nice update. Thank you!
Forum: A4 (B7 Platform) Discussion
04-06-2023, 10:21 AM
Replies: 14
Views: 9,001
Posted By 80sGuy

Yeah, glad I was able to tackle that flange....

Yeah, glad I was able to tackle that flange. Though it is 15 years old. Can't complain of the condition. It wasn't even leaking nor have any problems, I just felt like I needed to replace it as a...
Forum: A4 (B7 Platform) Discussion
04-06-2023, 08:37 AM
Replies: 14
Views: 9,001
Posted By 80sGuy

The entire cost of my kit: (Genuine Audi Parts)...

The entire cost of my kit:
(Genuine Audi Parts)
Timing Belt
Water Pump
Roller Upper
Roller Lower
Tensioner
$434 total shipped. It isn't bad at all!
Forum: A4 (B7 Platform) Discussion
04-06-2023, 08:29 AM
Replies: 14
Views: 9,001
Posted By 80sGuy

I already purchased all of them. I only use...

I already purchased all of them. I only use 'genuine parts', always have been on my cars. If you look at the pic, the original flange I took out is still in very good condition. If I were to replace...
Forum: A4 (B7 Platform) Discussion
04-06-2023, 06:18 AM
Replies: 14
Views: 9,001
Posted By 80sGuy

Thanks! Those were the exact o-rings I bought...

Thanks!
Those were the exact o-rings I bought from Amazon. Works like a charm. Car seems to drive better now (and feels better when braking to a halt) with less hesitations. How should I put it,...
Forum: A4 (B7 Platform) Discussion
04-04-2023, 01:44 PM
Replies: 14
Views: 9,001
Posted By 80sGuy

Just did this job. The original flange was still...

Just did this job. The original flange was still in very good condition after 15 years, and I'm sure if I stick a new o-ring on it it'll last for a long while. Initially I just wanted to 'rebuild' my...
Showing results 1 to 13 of 13


 
Forum Jump


All times are GMT -8. The time now is 10:40 PM.