Help: How to remove rear subwoofer?
#1
Audiworld Junior Member
Thread Starter
Join Date: May 2012
Location: Slovakia, Europe
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Help: Retrofitting and coding B&O
Hallo,
I am doing swap from standart speakers to B&O, does anyone knows how to remove rear speaker behind the rear seats under the window? It looks like from the inside and not from the truck place.
Thank you
I am doing swap from standart speakers to B&O, does anyone knows how to remove rear speaker behind the rear seats under the window? It looks like from the inside and not from the truck place.
Thank you
Last edited by badumi1; 02-11-2014 at 09:32 PM.
#2
AudiWorld Super User
Welcome to Audi World !
The rear shelf has to be removed from the interior to access the speakers.
Instructions say to remove:
- seat backrest
- armrest upper trim
- belt guides
- outer belt anchor
- D-pillar trim
- C-pillar trim
- speaker trim [Note: Speaker trim cannot be removed without destroying it.]
- 4 bolts in center
- unclip the shelf
- disengage from the shade
- pull forward and out
It may be possible to do without every step, but it sure looks complicated either way.
Not certain but you may need to swap to the B&O control module, recode and have CP removed.
If you decide to proceed I'm sure photos of the procedure would be appreciated by all.
The rear shelf has to be removed from the interior to access the speakers.
Instructions say to remove:
- seat backrest
- armrest upper trim
- belt guides
- outer belt anchor
- D-pillar trim
- C-pillar trim
- speaker trim [Note: Speaker trim cannot be removed without destroying it.]
- 4 bolts in center
- unclip the shelf
- disengage from the shade
- pull forward and out
It may be possible to do without every step, but it sure looks complicated either way.
Not certain but you may need to swap to the B&O control module, recode and have CP removed.
If you decide to proceed I'm sure photos of the procedure would be appreciated by all.
#3
Audiworld Junior Member
Thread Starter
Join Date: May 2012
Location: Slovakia, Europe
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Hallo,
It is done
I have done also protection at a dealer but still need to do a coding. Does anyone know how to code it as there is no security code for Sound system in vag com? Sometimes I get one high speaker pop of the dash and 2 does not and also sometimes mmi show B&O tone settings and then it is complete silent, when restart and get standart sound set up, all is ok.
Anyhow it is a night and day so far will post some pics of installation but it looks harder than it was. 1st I got complete wire installation of the car where B&O was used, then easier to use those wires only for the speakers.
Thank you
It is done
I have done also protection at a dealer but still need to do a coding. Does anyone know how to code it as there is no security code for Sound system in vag com? Sometimes I get one high speaker pop of the dash and 2 does not and also sometimes mmi show B&O tone settings and then it is complete silent, when restart and get standart sound set up, all is ok.
Anyhow it is a night and day so far will post some pics of installation but it looks harder than it was. 1st I got complete wire installation of the car where B&O was used, then easier to use those wires only for the speakers.
Thank you
Trending Topics
#8
Audiworld Junior Member
Thread Starter
Join Date: May 2012
Location: Slovakia, Europe
Posts: 13
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
ECS Tuning-Audi
A4 (B8 Platform) Discussion
21
09-11-2021 04:04 PM
bilbo6209
A6 / S6 (C5 Platform) Discussion
10
09-04-2015 04:07 PM
ECS Tuning-Audi
Audi A5 / S5 / RS5 Coupe & Cabrio (B8)
0
09-01-2015 08:27 AM