2005 a6 3.2L timing walk-thru needed!
#1
Audiworld Junior Member
Thread Starter
Join Date: Feb 2014
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
2005 a6 3.2L timing walk-thru needed!
So my tensioner failed on the passenger side and bent all the valves. Just got my final parts back from the machine shop and now time to put her back together. Only problem is I cannot find a diagram or walk-thru on setting the camshafts with the pistons and getting the timing right. I had to rotate the pistons after I removed the heads so I know everything is thrown off and need to realign everything before putting the timing chains back on. PLZ HELP!!!!!
#2
Bentley is pretty clear on this and it does not seem complicated. Pin the crank, install the locking tools on the cams, pretension the chains to remove slack, and tighten down the adjusters.
I'm doing the same job right now, but your damage must be worse than mine. I just replaced six intake valves, no machine work. I'm also doing the cam chain tensioners on both sided and all the guides for the lower chains (151k miles, so this seems like an opportunity).
Good luck!
I'm doing the same job right now, but your damage must be worse than mine. I just replaced six intake valves, no machine work. I'm also doing the cam chain tensioners on both sided and all the guides for the lower chains (151k miles, so this seems like an opportunity).
Good luck!
#3
Odd. I had typed up a full response, but this crappy format choked on it. I'm trying again, but not typing the whole thing again.
Cliff notes version is follow Bentley and use the tools.
Cliff notes version is follow Bentley and use the tools.
#4
Audiworld Junior Member
Thread Starter
Join Date: Feb 2014
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
Bentley is pretty clear on this and it does not seem complicated. Pin the crank, install the locking tools on the cams, pretension the chains to remove slack, and tighten down the adjusters.
I'm doing the same job right now, but your damage must be worse than mine. I just replaced six intake valves, no machine work. I'm also doing the cam chain tensioners on both sided and all the guides for the lower chains (151k miles, so this seems like an opportunity).
Good luck!
I'm doing the same job right now, but your damage must be worse than mine. I just replaced six intake valves, no machine work. I'm also doing the cam chain tensioners on both sided and all the guides for the lower chains (151k miles, so this seems like an opportunity).
Good luck!
Also replaced the top tensioners. And the guides on the block. Left the main tensioner and chains stock.
#5
Audiworld Junior Member
Thread Starter
Join Date: Feb 2014
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
Hey 4driver4 tried messaging you but ur inbox is full. Get at me when you get a chance. Maybe we can help each other out on this build. I know I could use it...
#6
Cams go into the head, then head on engine, then sprockets onto cams.
Since the heads are already on, you have to be very very careful installing the cams. When you put the cams in first, you can set them into the head so that none of the valves are open, so no spring tension is pushing back against he cap set. Once they are in, you can turn them to install the locking tool prior to installing the head.
However, since the head is already in place and the crank pin installed, you will need to be sure that you can get the cams into the head and turned to TDC without opening the valves on the cylinders where the pistons are at the top of their travel. If you install the locking tool on the cam before you bolt the cams into the head, take extreme care that you tighten the bolts (all 20 of them) a little at a time and evenly.
I'm not sure why you are worried about removing the sprocket; you have to loosen it anyway to set the cam timing.
Since the heads are already on, you have to be very very careful installing the cams. When you put the cams in first, you can set them into the head so that none of the valves are open, so no spring tension is pushing back against he cap set. Once they are in, you can turn them to install the locking tool prior to installing the head.
However, since the head is already in place and the crank pin installed, you will need to be sure that you can get the cams into the head and turned to TDC without opening the valves on the cylinders where the pistons are at the top of their travel. If you install the locking tool on the cam before you bolt the cams into the head, take extreme care that you tighten the bolts (all 20 of them) a little at a time and evenly.
I'm not sure why you are worried about removing the sprocket; you have to loosen it anyway to set the cam timing.
#7
Mine is close to do or die. I'm 3 o-rings short of installing the intake and hitting the key. Trans is in, exhaust is back in, heads are on, timing is set, etc.
3 o-rings.
Trending Topics
#8
Audiworld Junior Member
Thread Starter
Join Date: Feb 2014
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
Internals are done. Timing was actually easy. The trick I had to learn was to remove the heads off the camshafts then put them back on and torque the bolt when the chains tight while the cams are locked into the head. Now just covers and attach the accessories and ready to go back in!
#9
05 audi a6 3.2 lower and center timing chain walk-thru
Hey guys have anyone have had to remove the lower and center chain I had to do to failed tensioners. But now I can't find the timing diagram anywhere. I have all the specialty tools. Does anyone have a diagram or any solutions? THANKS
#10
Audiworld Junior Member
Thread Starter
Join Date: Feb 2014
Posts: 38
Likes: 0
Received 0 Likes
on
0 Posts
I left the lower tensioner alone. All the research I seen it was only the top tensioners failing. It was hard enough to do the top two I wasn't messing with the bottom as well. I found a program called alldata.com and paid a small fee and it gave me pretty good walk throughs on everything including torque settings and what not.