some random pics.... $5.06 maf housing and other cheap goodness inside...

Snow Trooper Is Numb · 12-23-2005, 10:11 PM

So the elcheapo maf housing has been on with a new sensor and intake setup for a few days now. Car has never ran better. Got it locked down to 12.5 A/F tapering to 12:1 after 7000rpms, killer timing and super safe CF and KSV all on pump (laptop is forked, no logs, since I know some will ask. will get a FATS run and some logs asap). By using some scrap 4 inch thinwall tubing from my old turbo diesel exhaust and some really overkill silicon couplers made for diesel turbos that see over 100 psi (funny side note, i couldnt find 4" I.D. couplers anywhere local. all places to order them from where about $32 each for 3" sections. go this at the Semi supply shop for $19.50 per foot) so over all cost for this setup including the new AEM Dryflow 4" cone filter that is oil free to prevent damage to the sensor was $66.56.

some pics:

These new filters from AEM are badass, very very high quality design... NO more oil!!!!!!!

The glorious HD 88mm maf housing.

hmmm, whats going on in the red circle?

mandatory matching wheel and y-pipe shot, i am such a ricer.

btw- car is filthy, has been raining and snowing all week. otherwise i would get some daytime shots with the new seats

mmmmm kevlar

AUDIS4BI:Vintage · 12-23-2005, 10:26 PM

EVO MS Intake shield wrapped in cool-it Thermo heat resistant mat and high quality duct tape;P

DeutschDriver · 12-23-2005, 11:07 PM

nhkayalker17 · 12-23-2005, 11:12 PM

Stage 3 intake for $66?!?!?! Holy schnikes, Batman!

SIMPPLY @ WMS · 12-23-2005, 11:19 PM

AUDIS4BI:Vintage · 12-23-2005, 11:33 PM

http://forums.audiworld.com/s4/msgs/2210218.phtml

VR_Life · 12-24-2005, 12:35 AM

http://www.thermotec.com/products/full/12005/12005.html

VR_Life · 12-24-2005, 12:52 AM

But that was for my UrS4 project ;-)

Snow Trooper Is Numb · 12-24-2005, 12:52 AM

sheild is pretty effective along with all hotside components being ceramic coated on my car

Snow Trooper Is Numb · 12-24-2005, 12:54 AM

and all around heavy duty supply place. this stuff is super nice, got the really thick wrapped outer layer, burst preasure is like 200psi and withstands temps over 300 degrees

12-23-2005, 10:11 PM	#1
Snow Trooper Is Numb Junior Member Garage is empty, add now Join Date: Dec 2005 Posts: 826	some random pics.... $5.06 maf housing and other cheap goodness inside... So the elcheapo maf housing has been on with a new sensor and intake setup for a few days now. Car has never ran better. Got it locked down to 12.5 A/F tapering to 12:1 after 7000rpms, killer timing and super safe CF and KSV all on pump (laptop is forked, no logs, since I know some will ask. will get a FATS run and some logs asap). By using some scrap 4 inch thinwall tubing from my old turbo diesel exhaust and some really overkill silicon couplers made for diesel turbos that see over 100 psi (funny side note, i couldnt find 4" I.D. couplers anywhere local. all places to order them from where about $32 each for 3" sections. go this at the Semi supply shop for $19.50 per foot) so over all cost for this setup including the new AEM Dryflow 4" cone filter that is oil free to prevent damage to the sensor was $66.56. some pics: These new filters from AEM are badass, very very high quality design... NO more oil!!!!!!! The glorious HD 88mm maf housing. hmmm, whats going on in the red circle? mandatory matching wheel and y-pipe shot, i am such a ricer. btw- car is filthy, has been raining and snowing all week. otherwise i would get some daytime shots with the new seats mmmmm kevlar

12-23-2005, 10:26 PM	#2
AUDIS4BI:Vintage AudiWorld Super User Garage is empty, add now Join Date: Jul 2003 Posts: 12,577	Your ghetto fab riced out project isn't done yet...you're missing this.. EVO MS Intake shield wrapped in cool-it Thermo heat resistant mat and high quality duct tape;P __________________

12-23-2005, 11:07 PM	#3
DeutschDriver Senior Member Garage is empty, add now Join Date: May 2004 Posts: 6,149	very clean for homebrew __________________ 2001 S4 Avant Silver / Onyx 6 Speed, Premium, Bose, Cold Totally stock for now... ;-) <rollseyes> Crappy day? Read this. What every n00b should know.

12-23-2005, 11:12 PM	#4
nhkayalker17 Junior Member Garage is empty, add now Join Date: May 2005 Posts: 773	Wow, it actually looks good. I'd love to see some more on this DIY mod. Stage 3 intake for $66?!?!?! Holy schnikes, Batman! __________________ "And Caesar's ghost, roaming about in search of revenge, with hate at his side still hot from hell,will in these boundries with a ruler's voice cry 'HAVOC' and let slip the dogs of war. And these terrible acts will smell above the earth, with rotting corpses begging to be burried."

12-23-2005, 11:19 PM	#5
SIMPPLY @ WMS Former Vendor 2000 Audi S4 Join Date: Apr 2004 Posts: 5,978	yuck wth did you do ?

12-23-2005, 11:33 PM	#6
AUDIS4BI:Vintage AudiWorld Super User Garage is empty, add now Join Date: Jul 2003 Posts: 12,577	I got dirrrty wit it lol.. Here is the write up.LOL http://forums.audiworld.com/s4/msgs/2210218.phtml __________________

12-24-2005, 12:35 AM	#7
VR_Life Guest Garage is empty, add now Join Date: Jul 2003 Posts: 9,718	The duct tape will peel the moment it gets hot. Buy some thermotec tape or adhesive spray http://www.thermotec.com/products/full/12005/12005.html

12-24-2005, 12:52 AM	#8
VR_Life Guest Garage is empty, add now Join Date: Jul 2003 Posts: 9,718	I also bought lots of silicone coupling from local International Truck parts shop - cheaper But that was for my UrS4 project ;-)

12-24-2005, 12:52 AM	#9
Snow Trooper Is Numb Junior Member Garage is empty, add now Join Date: Dec 2005 Posts: 826	the duct tape will get all gooey, i feel that while simple, the standard evo sheild is pretty effective along with all hotside components being ceramic coated on my car

12-24-2005, 12:54 AM	#10
Snow Trooper Is Numb Junior Member Garage is empty, add now Join Date: Dec 2005 Posts: 826	bingo, this was a place called Williams Oil filter service, international dealer and all around heavy duty supply place. this stuff is super nice, got the really thick wrapped outer layer, burst preasure is like 200psi and withstands temps over 300 degrees

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode


Discussion Forums: