World's Fastest S4 Dragstrip Run -- 11.812 @ 118.38mph!!!

The Big Blue Machine · 11-25-2003, 11:32 PM

Well, I decided to head on down to Atco Raceway tonight to get some runs in with the new FMIC and ramair intake. On my way to the track I blew another MAF sensor and was thinking the car felt slow... I was getting 0.00 g/s which was pretty odd since I was getting between .042 and .078 g/s when my last one bit the dust. Anyway, I should have known better not to get upset, as Blitz kept telling me his car ran its best times on speed density. :-)

At first, I made a few 12.0 to 12.2 passes @ 116-117, but I was only pulling 1.8 to 1.9 short times. I knew she had at least an 11.8 to 11.9 in her based on the traps. I let some air out of the tires and voila, an 11.98 @ 117.69mph with a 1.76 60ft. On my next run, I tried coming out slightly harder (about 4300rpms) and I blew the clutch away instantly through all of 1st gear. On my last run of the night, I pulled a 1.701 60ft leading to an 11.812 @ 118.38mph!!

I have all of my runs on video except for the last one, the 11.8...turns out my friend was freezing his ass off and went to go get hot chocolate on that run. LOL. Oh well, at least I have the 11.98 on video and the 11.8 timeslip.

Track Vitals:

Atco Raceway, Atco, NJ
Temperature: 32-40 degrees
Gas: 100 Cam2/94 mix
Full Weight including interior, tools, etc.

Keep in mind these runs were all made without any aquamist water injection (I need to get new fittings since going with the FMIC). I guess you can throw R1eater's theory out the window that the only reason my car is faster than his is because of the water injection. I will, however, be needing it if I want to duplicate that 11.8 on pure pump gas the next time out. :-)

I'd like to thank Mark (SilverBullet) and Ant (Blitz) for their help and support. Ant told me I could expect 2 tenths and 2mph with his ramair/FMIC setup. Ant also told me these cars run their fastest times using speed density instead of MAF. Then finally he said that the stuff people were saying about my car having to be re-tuned by Sportec for the FMIC and ramair was absolute nonsense. He was right on the money with everything!

Laters,

Marc

P.S. Running speed density killed two birds with one stone... Not only do I not have to worry about replacing costly MAF sensors anymore, but I also don't have to worry about my "fuel bank too rich" codes that have been driving me crazy. Those put you into limp mode unless you run speed density. With speed density, there are no codes at all except for the obvious MAF sensor voltage too low...

The 11.98 Video

golfrsi · 11-25-2003, 11:36 PM

are you blowing the bosch MAF or the Hitachi?

The Big Blue Machine · 11-25-2003, 11:38 PM

The Big Blue Machine · 11-25-2003, 11:46 PM

APR Stage III Kit
RS4 clutch, MAF, & fuel pump
Sportec injectors
Sportec tuned 103 octane chip
Milltek dual exhaust
Milltek downpipes w/high flow cats
ERL Aquamist Water Injection 1s System (not currently hooked up)
Forge BPVs
AWE aluminum flywheel
Blitz ported intake manifold
Blitz/McNeil custom FMIC
Blitz/McNeil custom ramair
APR Level 3 Brakes
Koni Shocks
Intrax Springs

No More B5 S4 · 11-25-2003, 11:48 PM

The Big Blue Machine · 11-25-2003, 11:50 PM

J.Moss@TorqueFactory · 11-25-2003, 11:54 PM

Yossarian · 11-25-2003, 11:59 PM

The Big Blue Machine · 11-26-2003, 12:05 AM

He'd blow a MAF sensor, replace it, only to have the "new" one go bad after just a couple days. He wound up running his car without the MAF sensor and that produced his best times...

I really wish I could have done some back to back runs with the MAF vs speed density, but I guess that'll have to wait until someone donates me a new MAF sensor since I'm now broke after buying the FMIC/ramair. LOL.

AudiJon · 11-26-2003, 12:18 AM

But they didn't ask you to leave after running faster than a 12.000 1/4 mile? I was under the impression that cars faster than 12 seconds were required to have a roll cage...

11-25-2003, 11:32 PM	#1
The Big Blue Machine Junior Member Account #: 61928 Join Date: Sep 2003 Posts: 960	World's Fastest S4 Dragstrip Run -- 11.812 @ 118.38mph!!! Well, I decided to head on down to Atco Raceway tonight to get some runs in with the new FMIC and ramair intake. On my way to the track I blew another MAF sensor and was thinking the car felt slow... I was getting 0.00 g/s which was pretty odd since I was getting between .042 and .078 g/s when my last one bit the dust. Anyway, I should have known better not to get upset, as Blitz kept telling me his car ran its best times on speed density. :-) At first, I made a few 12.0 to 12.2 passes @ 116-117, but I was only pulling 1.8 to 1.9 short times. I knew she had at least an 11.8 to 11.9 in her based on the traps. I let some air out of the tires and voila, an 11.98 @ 117.69mph with a 1.76 60ft. On my next run, I tried coming out slightly harder (about 4300rpms) and I blew the clutch away instantly through all of 1st gear. On my last run of the night, I pulled a 1.701 60ft leading to an 11.812 @ 118.38mph!! I have all of my runs on video except for the last one, the 11.8...turns out my friend was freezing his ass off and went to go get hot chocolate on that run. LOL. Oh well, at least I have the 11.98 on video and the 11.8 timeslip. Track Vitals: Atco Raceway, Atco, NJ Temperature: 32-40 degrees Gas: 100 Cam2/94 mix Full Weight including interior, tools, etc. Keep in mind these runs were all made without any aquamist water injection (I need to get new fittings since going with the FMIC). I guess you can throw R1eater's theory out the window that the only reason my car is faster than his is because of the water injection. I will, however, be needing it if I want to duplicate that 11.8 on pure pump gas the next time out. :-) I'd like to thank Mark (SilverBullet) and Ant (Blitz) for their help and support. Ant told me I could expect 2 tenths and 2mph with his ramair/FMIC setup. Ant also told me these cars run their fastest times using speed density instead of MAF. Then finally he said that the stuff people were saying about my car having to be re-tuned by Sportec for the FMIC and ramair was absolute nonsense. He was right on the money with everything! Laters, Marc P.S. Running speed density killed two birds with one stone... Not only do I not have to worry about replacing costly MAF sensors anymore, but I also don't have to worry about my "fuel bank too rich" codes that have been driving me crazy. Those put you into limp mode unless you run speed density. With speed density, there are no codes at all except for the obvious MAF sensor voltage too low... The 11.98 Video

11-25-2003, 11:36 PM	#2
golfrsi AudiWorld Senior Member Account #: 46784 Join Date: Nov 2002 Location: Philadelphia, PA Posts: 3,788	Congrats!!!! question though... are you blowing the bosch MAF or the Hitachi?

11-25-2003, 11:38 PM	#3
The Big Blue Machine Junior Member Account #: 61928 Join Date: Sep 2003 Posts: 960	Bosch. I'm starting to wonder what would be involved in converting to Hitachi... Thanx, BTW.

11-25-2003, 11:46 PM	#4
The Big Blue Machine Junior Member Account #: 61928 Join Date: Sep 2003 Posts: 960	Here's a list of my mods... APR Stage III Kit RS4 clutch, MAF, & fuel pump Sportec injectors Sportec tuned 103 octane chip Milltek dual exhaust Milltek downpipes w/high flow cats ERL Aquamist Water Injection 1s System (not currently hooked up) Forge BPVs AWE aluminum flywheel Blitz ported intake manifold Blitz/McNeil custom FMIC Blitz/McNeil custom ramair APR Level 3 Brakes Koni Shocks Intrax Springs

11-25-2003, 11:48 PM	#5
No More B5 S4 Elder Member Account #: 41217 Join Date: Aug 2002 Posts: 30,774	Congrats! Any more info on the speed density set-up alternative to MAF? TIA! __________________ --------------------------------------------------------- "The Lord be with your spirit. Grace be with you." -2 Timothy 4:22 Click for Peer FATS Times. Updated: 03/15/05<a href="http://public.fotki.com/s4madman/scenerylandscape/wallpapers_1600x1200/"> Got Wallpapers? Updated: 10/29/04</a> The AW Database. Updated: 02/15/05

11-25-2003, 11:50 PM	#6
The Big Blue Machine Junior Member Account #: 61928 Join Date: Sep 2003 Posts: 960	Yeah, all you have to do is disconnect your MAF sensor connector. =)

11-25-2003, 11:54 PM	#7
J.Moss@TorqueFactory Senior Member Account #: 15175 Join Date: Jan 2001 Posts: 5,077	Kick-Ass times! Congratulations! What is your thoughts on the MAF problems? __________________ Sport Compact Car 2007 Ultimate Street Car Challenge Winner Jeff Moss, ASE Certified (A1, A3, A4, A5, A6, A8) <a href="http://www.torque-factory.com">Los Angeles area GIAC dealer for Audi, Bentley, BMW, Mini, Porsche and VW. Torque-Factory, Inc.</a> Torque-Factory Support Forum

11-25-2003, 11:59 PM	#8
Yossarian Junior Member Account #: 19731 Join Date: May 2001 Posts: 1,304	Awesome!

11-26-2003, 12:05 AM	#9
The Big Blue Machine Junior Member Account #: 61928 Join Date: Sep 2003 Posts: 960	No idea, but Blitz went through the same thing he said... He'd blow a MAF sensor, replace it, only to have the "new" one go bad after just a couple days. He wound up running his car without the MAF sensor and that produced his best times... I really wish I could have done some back to back runs with the MAF vs speed density, but I guess that'll have to wait until someone donates me a new MAF sensor since I'm now broke after buying the FMIC/ramair. LOL.

11-26-2003, 12:18 AM	#10
AudiJon Elder Member Account #: 31005 Join Date: Jan 2002 Posts: 12,992	Congrats! That's awesome! But they didn't ask you to leave after running faster than a 12.000 1/4 mile? I was under the impression that cars faster than 12 seconds were required to have a roll cage... __________________ IM: JonMiller3

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode


Discussion Forums:	Advanced Search