Audi Chassis Codes?
#1
Audi Chassis Codes?
I have a 2002 Audi A6 Avant Quattro with 3.0 engine. I am getting the following codes.
P0421: Warm Up Catalyst Efficiency Below Threshold (Bank 1)
C06EE: Unknown code
C0759: Unknown code
I am not worried about the P0421.
I am worried about the Chassis codes and cannot find anywhere that will explain what they are.
I just had a local guy change all the belts and I am afraid something got screwed up.
Does anyone have any idea what the chassis codes mean and they cause?
P0421: Warm Up Catalyst Efficiency Below Threshold (Bank 1)
C06EE: Unknown code
C0759: Unknown code
I am not worried about the P0421.
I am worried about the Chassis codes and cannot find anywhere that will explain what they are.
I just had a local guy change all the belts and I am afraid something got screwed up.
Does anyone have any idea what the chassis codes mean and they cause?
#4
AudiWorld Super User
I have a 2002 Audi A6 Avant Quattro with 3.0 engine. I am getting the following codes.
P0421: Warm Up Catalyst Efficiency Below Threshold (Bank 1)
C06EE: Unknown code
C0759: Unknown code
I am not worried about the P0421.
I am worried about the Chassis codes and cannot find anywhere that will explain what they are.
I just had a local guy change all the belts and I am afraid something got screwed up.
Does anyone have any idea what the chassis codes mean and they cause?
P0421: Warm Up Catalyst Efficiency Below Threshold (Bank 1)
C06EE: Unknown code
C0759: Unknown code
I am not worried about the P0421.
I am worried about the Chassis codes and cannot find anywhere that will explain what they are.
I just had a local guy change all the belts and I am afraid something got screwed up.
Does anyone have any idea what the chassis codes mean and they cause?
I ran with the error for at least 18 months and then was shocked at my fuel efficiency gain when I finally did replace my linkage armatures. Oh well, that money is long gone. Pull your engine cover off and see if your armatures are broken. Very inexpensive 15 min fix.
#6
AudiWorld Super User
I changed both the motors and the levers. One motor had gone bad and both levers had snapped. The bad motor simply would not maintain pressure.
#7
AudiWorld Super User
You're extremely lucky the rods hadn't frozen in the manifold….99% of the time that is the cause of the links or the vacuum motors breaking.
Trending Topics
#8
AudiWorld Super User
Yes. I had identified them as broken and had thoroughly prepared myself for the Dremel fixing technique outlined on this forum. I even purchased a Dremel. I had to do some unrelated work at an Audi service department and 'casually' mentioned to the tech that I was looking to replace my levers and wondered if they sold the vacuum motors individually. He walked out to my car, pooped the cover off and spent ten minutes tweaking and twisting and said finally that the rods were not frozen and I was right, my problem was the motors which I was insane to by from their parts department. He recommended lambo, I ended up getting rover.
#9
My P0421 code cleared up when I replaced my linkage armature. Not sure if that is a rule or a coincidence.
I ran with the error for at least 18 months and then was shocked at my fuel efficiency gain when I finally did replace my linkage armatures. Oh well, that money is long gone. Pull your engine cover off and see if your armatures are broken. Very inexpensive 15 min fix.
I ran with the error for at least 18 months and then was shocked at my fuel efficiency gain when I finally did replace my linkage armatures. Oh well, that money is long gone. Pull your engine cover off and see if your armatures are broken. Very inexpensive 15 min fix.
#10
AudiWorld Super User
Here is my thread on this. Simple to check. Just pull up your engine cover and look at the levers and motors.
https://www.audiworld.com/forums/sho....php?t=2852103
Caveats, I am not familiar with the 3.0 engine, and I did not own my VAG at the time so I was relying on the old replace a part and drive and see if the code clears. In this case, the CEL cleared and when I did return to my mech, the code was no longer present... then I moved on to vacuum issues later. :-)
https://www.audiworld.com/forums/sho....php?t=2852103
Caveats, I am not familiar with the 3.0 engine, and I did not own my VAG at the time so I was relying on the old replace a part and drive and see if the code clears. In this case, the CEL cleared and when I did return to my mech, the code was no longer present... then I moved on to vacuum issues later. :-)
Last edited by A4 Phil; 12-30-2013 at 04:28 AM.