AudiWorld Forums

 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: tonyj
Showing results 1 to 25 of 497
Search took 0.73 seconds.
Forum: Audi 5000 / 200 / V8 Discussion
01-04-2022, 02:38 PM
Replies: 4
Views: 548
Posted By tonyj

I would also suspect the ignition switch.

I would also suspect the ignition switch.
Forum: Audi 5000 / 200 / V8 Discussion
12-30-2021, 08:29 PM
Replies: 1
Views: 444
Posted By tonyj

Used to spend a lot of time on T44s. I have...

Used to spend a lot of time on T44s. I have changed several high / low beam signal switches. As I remember I had success at removing them and inventing a fix..

The article you posted is correct....
Forum: A4 (B6 Platform) Discussion
04-05-2009, 07:49 PM
Replies: 3
Views: 11,915
Posted By tonyj

If the sound changes when you turn slightly from...

If the sound changes when you turn slightly from one side to the other I would guess wheel bearing.
Forum: A4 (B6 Platform) Discussion
03-15-2009, 02:03 PM
Replies: 5
Views: 556
Posted By tonyj

The shafts on either end of #6 bind up. Remove...

The shafts on either end of #6 bind up. Remove and grease them.
Forum: A4 (B6 Platform) Discussion
03-01-2009, 07:57 PM
Replies: 11
Views: 1,007
Posted By tonyj

Try using an open end wrench of the appropriate...

Try using an open end wrench of the appropriate size to pry up evenly.
Forum: A4 (B6 Platform) Discussion
02-02-2009, 05:49 PM
Replies: 2
Views: 370
Posted By tonyj

I had exactly the same gas cap experience a few...

I had exactly the same gas cap experience a few weeks ago. $32 from Mpls dealer.
Forum: A4 (B6 Platform) Discussion
01-21-2009, 07:33 PM
Replies: 9
Views: 687
Posted By tonyj

mileage suggestions

pull the codes.

Check O2 sensors.

Failing temperature sensor.

Techron injector cleaner would be a good thing to try.
Forum: A4 (B6 Platform) Discussion
01-12-2009, 09:49 PM
Replies: 32
Views: 2,512
Posted By tonyj

Loose steering rack mount?

Loose steering rack mount?
Forum: A4 (B6 Platform) Discussion
12-31-2008, 09:41 AM
Replies: 22
Views: 5,974
Posted By tonyj

2nd on a new O2 sensor. My '04 1.8 6M is getting 26 -27 average driving

and 32 on highway in recent weeks. Chang O2 and 2nd on checking the MAF also.
Pull codes.
Forum: A4 (B6 Platform) Discussion
12-28-2008, 10:10 PM
Replies: 3
Views: 296
Posted By tonyj

Re: Great pic. Looks just like mine but a bit...

Re: Great pic. Looks just like mine but a bit cleaner and warmer.
Forum: A4 (B6 Platform) Discussion
12-28-2008, 10:10 PM
Replies: 3
Views: 296
Posted By tonyj

Great pic. Looks just like mine.

Great pic. Looks just like mine.
Forum: VAG-COM Discussion
12-28-2008, 09:57 PM
Replies: 2
Views: 804
Posted By tonyj

It looks like a number of item need to be checked.

We plan to pull the HPFP to look as the cam lobe and follower.
Forum: VAG-COM Discussion
12-26-2008, 08:44 PM
Replies: 10
Views: 6,319
Posted By tonyj

Thank you so much for the help. We will get busy...

Thank you so much for the help. We will get busy on this list.
Forum: VAG-COM Discussion
12-26-2008, 09:32 AM
Replies: 2
Views: 804
Posted By tonyj

Update on the codes '06 A4 2.0 cam / High pressure fuel pump issue

The codes might be a failing cam lobe but the tech wants more confirmation.<ul><li><a...
Forum: VAG-COM Discussion
12-23-2008, 09:51 PM
Replies: 10
Views: 6,319
Posted By tonyj

Update from Audi Dealer diagnostic tech

My son took the car to the local dealer here in Minneapolis (Carosel) and had a tech that seemed knowledgeable look at the codes.
He said that the two codes that are listed on the cam lobe wear TSB...
Forum: VAG-COM Discussion
11-11-2008, 10:52 AM
Replies: 10
Views: 6,319
Posted By tonyj

After more web searching I am beginning to suspect HP fuel pump cam follower

and/or Worn cam lob for HP fuel pump due to wear on the cam which may be the one-piece Rev A cam.
When my son returns we will check if he has rev A or B cam and check the FP cam lob follower for...
Forum: VAG-COM Discussion
11-10-2008, 06:14 PM
Replies: 10
Views: 6,319
Posted By tonyj

Here is the freeze frame - longer version. I wasn't sure how to interpret that

8 Faults Found:
001602 - Sensor Reference Voltage A: Circuit: Low
P0642 - 002 - Lower Limit Exceeded - Intermittent
Freeze Frame:
Fault Status:...
Forum: VAG-COM Discussion
11-09-2008, 09:21 AM
Replies: 10
Views: 6,319
Posted By tonyj

We didn't have a current VAG system before the CEL began to appear

After the codes we upgraded the system to the current cable and software and then pulled these codes.
I will tell him to clear codes and then check again. It may take a month or so because he will...
Forum: VAG-COM Discussion
11-04-2008, 01:27 PM
Replies: 10
Views: 6,319
Posted By tonyj

Ideas on a range of codes. '06 A42.0TQ6M

This is an '06 A4 2.0TQ6M and we are a looking for suggestions on the cause of these codes that occurred after a bit of spirited driving.

8 Faults Found:
001602 - Sensor Reference Voltage A:...
Forum: A4 (B6 Platform) Discussion
11-04-2008, 11:50 AM
Replies: 6
Views: 904
Posted By tonyj

Or air int he system, failed coolant pump ....

Or air int he system, failed coolant pump ....
Forum: A4 (B6 Platform) Discussion
10-24-2008, 02:38 PM
Replies: 3
Views: 353
Posted By tonyj

Maybe the clutch master or slave cylinder is...

Maybe the clutch master or slave cylinder is binding.
Forum: A4 (B6 Platform) Discussion
09-04-2008, 06:37 PM
Replies: 7
Views: 372
Posted By tonyj

Mine is now loud enough in 1st that people near the car hear it easily

I have changed the trans oil but it didn't help.

I have been driving it like this for over 10K and it has gotten somewhat worse but it seems to have leveled off in recent months.

I plan to...
Forum: A4 (B6 Platform) Discussion
08-21-2008, 06:46 PM
Replies: 8
Views: 1,364
Posted By tonyj

Its a coil pack. Mine was the same when the first...

Its a coil pack. Mine was the same when the first onw went out.
Forum: A4 (B6 Platform) Discussion
08-08-2008, 11:34 AM
Replies: 8
Views: 378
Posted By tonyj

I just had this fun project last week - '04 1.8TQ6M

I tried to use CA but it didn't work. It didn't look like epoxy would have bonded to the plastic.

I ended up fabing a piece of brass sheet 1/2 inch wide and bent to ~90 degrees then pop riveted it...
Forum: A4 (B6 Platform) Discussion
07-30-2008, 02:03 PM
Replies: 12
Views: 431
Posted By tonyj

Your may want to check the Colorado laws on this.

Here in Minnesota there is a law that requires that the customer be shown the old parts. No parts, No pay.
Showing results 1 to 25 of 497
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 01:10 AM.