AudiWorld Forums

 
Page 1 of 13
1
2
3
11
Last »
Search: Posts Made By: superv
Showing results 1 to 25 of 325
Search took 0.60 seconds.
Forum: A4 (B5 Platform) Discussion
05-08-2006, 07:56 AM
Replies: 2
Views: 243
Posted By superv

Great

It looked a little strange and made using the spring compressor more difficult. I had to get tricky.

I'm pretty excited about the new setup. Props to PureMS for a great setup, despite the...
Forum: A4 (B5 Platform) Discussion
05-08-2006, 06:43 AM
Replies: 2
Views: 243
Posted By superv

Vogtland Club Spec rear springs touching?

I just installed my Vogtland Club Spec springs and bilstein sport shocks yesterday. I have a question about the rear springs. They looked like they were progressive rate springs because the coils...
Forum: A4 (B5 Platform) Discussion
04-13-2006, 12:07 PM
Replies: 9
Views: 171
Posted By superv

893-711-237-B

there are 11 in the USA, all of them in NJ.
Forum: A4 (B5 Platform) Discussion
04-13-2006, 08:59 AM
Replies: 9
Views: 171
Posted By superv

Re: My torx bit went back underneath where the e-brake and cupholder are...

thats what it sound like to me. There is a good write up in the tech article about how to remove the center console.
Forum: A4 (B5 Platform) Discussion
04-13-2006, 08:24 AM
Replies: 9
Views: 171
Posted By superv

there is a 4th,

Items can also get into the center console, which I have checked. It slipped out of my hand near the rear of the shifter housing, so that kind of eminated the boot. On the way to the ground I think...
Forum: A4 (B5 Platform) Discussion
04-13-2006, 08:15 AM
Replies: 9
Views: 171
Posted By superv

into the drive shaft area?

I think I dropped into into the drive train tunnel. It did not fall onto the ground. I removed the entire center console so its not under there. I guess it sitting somewhere on top of the...
Forum: A4 (B5 Platform) Discussion
04-13-2006, 07:20 AM
Replies: 9
Views: 171
Posted By superv

Part number of shifter washer??

Can someone with a parts CD find the part number for the large aluminum rectangle washer that is used to connect the shifter linkage to the transmission selector rod? I lost mine during my V&S ss...
Forum: A4 (B5 Platform) Discussion
04-12-2006, 07:33 PM
Replies: 15
Views: 347
Posted By superv

I lost the rectangle washer!!

I drop the aluminum rectangle washer that connects the shifter linkage to the selector rod! It is described in step number 7. ...
Forum: A4 (B5 Platform) Discussion
04-12-2006, 02:12 PM
Replies: 15
Views: 347
Posted By superv

my last scabs just healed

I'll be ready with the bandaid and neosporen. I have a 98.5 also
Forum: A4 (B5 Platform) Discussion
04-12-2006, 12:30 PM
Replies: 15
Views: 347
Posted By superv

Circlip pliers?

Would you suggest straight tips or the curved tips? Should they work like standard pliers or should they be reverse pliers (when you close the hand grip the tool side gets farther apart)?
Forum: A4 (B5 Platform) Discussion
04-12-2006, 11:58 AM
Replies: 15
Views: 347
Posted By superv

V&S short shifter install tips?

I have read through the install instructions on thier web site and the article on the tech articles, but I'm wondering if anyone has any advice or tips that isn't listed in those areas. I am most...
Forum: A4 (B5 Platform) Discussion
04-05-2006, 07:54 AM
Replies: 19
Views: 424
Posted By superv

Re: High engagment doesn't bother me just checking :)

if it doesn't bother you then don't change anything.
Forum: A4 (B5 Platform) Discussion
04-05-2006, 07:51 AM
Replies: 19
Views: 424
Posted By superv

do not make assumptions I have any inabilities.

I have driven my A4 smoothly for years. I just prefer the shorter clutch throw.
Forum: A4 (B5 Platform) Discussion
04-05-2006, 07:39 AM
Replies: 19
Views: 424
Posted By superv

if you don't like the high engagment...

you can make a clutch stop. basically you just put something behind the clutch pedal so it doesn't travel so far (shorter throw). I did it and couldn't be happier.

search for clutch stop
Forum: A4 (B5 Platform) Discussion
04-03-2006, 11:53 AM
Replies: 12
Views: 463
Posted By superv

short block or long block?

which one is more of a direct replacement for the standard 1.8T? AEB?
Forum: A4 (B5 Platform) Discussion
04-03-2006, 11:47 AM
Replies: 2
Views: 298
Posted By superv

strut mounts

I don't have any clunking from my suspension now, but would it be worth it to replace the strut mounts. I notice PureMS and ECS both sell them. Are they for the fronts only?
Forum: A4 (B5 Platform) Discussion
04-03-2006, 06:54 AM
Replies: 2
Views: 298
Posted By superv

Shock and Spring install, what else should be replaced.

I have deciede to replace my aging shocks and springs, with Bilstein sports and vogtland club specs. During the installation process should anything else be replaced while I have the suspension torn...
Forum: A4 (B5 Platform) Discussion
03-21-2006, 10:04 AM
Replies: 3
Views: 287
Posted By superv

Making a clutch stop

I have decided to make a clutch stop for my A4. For those of you that have made a clutch stop; How did you determine how thick to make your clutch stop? My plan was to use rubber bands and wooden...
Forum: A4 (B5 Platform) Discussion
11-28-2005, 10:19 AM
Replies: 5
Views: 507
Posted By superv

no way.

I'm in Portland, OR. In Portland if cars are new enough they just hook up to the ODBII port. If they would have actually checked the exhaust I would have definately failed.
Forum: A4 (B5 Platform) Discussion
11-28-2005, 10:02 AM
Replies: 5
Views: 507
Posted By superv

Test Pipe and DEQ, success!

I just wanted to let you anyone know that I sucessfully passed my states Department of Environmental Quality test with no cat. I have a test pipe and used the a resistor from Radio shack soldered...
Forum: Audio, Video and Security Discussion
11-07-2005, 01:32 PM
Replies: 1
Views: 802
Posted By superv

1998 A4 Bose Tweeter rattling

Hello, The left front tweeter in my 1998.5 A4, with the Bose system, is rattleing badly so I think that it is probably blown. Overall I like the sounds sytem and would like to spend as little as...
Forum: A4 (B5 Platform) Discussion
09-16-2005, 12:02 PM
Replies: 6
Views: 458
Posted By superv

replacing a syncro. How much $?

I believe that my second gear syncro is starting to go bad. It is much much harder to get into gear than it ever hase. Can I take it to an independent tranny shop or does it have to go the...
Forum: A4 (B5 Platform) Discussion
09-16-2005, 11:52 AM
Replies: 36
Views: 618
Posted By superv

dying 2nd gear?

Mine is starting to go. I think the syncros are starting to go because getting into gear is much harder. Have you had your transmission repaired? how much did it cost?
Forum: A4 (B5 Platform) Discussion
09-12-2005, 10:09 AM
Replies: 5
Views: 283
Posted By superv

Neuspeed ECU, socketed or soldered

Hello, I sent my ECU to Neuspeed a couple years ago to have a 1bar chip put in. I never opened it up to see if it was socketed or if they just soldered the chip in. Can anyone tell me how Neuspeed...
Forum: 1.8T Discussion
09-12-2005, 10:07 AM
Replies: 2
Views: 590
Posted By superv

Neuspeed ECU, socketed or soldered

Hello, I sent my ECU to Neuspeed a couple years ago to have a 1bar chip put in. I never opened it up to see if it was socketed or if they just soldered the chip in. Can anyone tell me how Neuspeed...
Showing results 1 to 25 of 325
 
Page 1 of 13
1
2
3
11
Last »


 
Forum Jump


All times are GMT -8. The time now is 09:13 PM.