Any way to disable adaptive light warning?
#11
AudiWorld Super User
For the most recent couple of posts with issues, the codes probably lead to either an internal issue w/ the specified light unit, OR a wiring/connection issue. I would certainly try the latter first given cost & difficulty replacing units. Simplest is just undoing given connector, using some cleaner and reattaching. Still have to dive into fender liner to get there. Per Mister Bally's post, see if anything is obviously loose.
It's further down in the post, but it could also be connector or wires right near it. Mine have always been trouble free, but have definitely had connector issues with the O2's on the W12. Ultimately cleaning there doesn't fix longer term, but changing end connector and wires with crimped terminals close in definitely does. Audi sells virtually any wiring end connector I have ever needed, and they have wiring leads with pre crimped ends in various sizes and types. Here though very hard to isolate as between headlight unit and wiring without a known good unit to check against. Not sure if reversing units temporarily works and then can deduce if it is unit, or wiring to unit. A bunch of disassembly to get to that though.
It's further down in the post, but it could also be connector or wires right near it. Mine have always been trouble free, but have definitely had connector issues with the O2's on the W12. Ultimately cleaning there doesn't fix longer term, but changing end connector and wires with crimped terminals close in definitely does. Audi sells virtually any wiring end connector I have ever needed, and they have wiring leads with pre crimped ends in various sizes and types. Here though very hard to isolate as between headlight unit and wiring without a known good unit to check against. Not sure if reversing units temporarily works and then can deduce if it is unit, or wiring to unit. A bunch of disassembly to get to that though.
Last edited by MP4.2+6.0; 10-16-2015 at 09:15 AM.
#12
Agreed. Of course, the symptom besides the MIL is the curve light not working on one or both sides. Here's the data I pulled with VAG-COM:
Address 55: Xenon Range Labels: 4F0-910-357.lbl
Part No SW: 4F0 910 357 F HW: 4F0 907 357 F
Component: AFS 1 H01 0020
Revision: 00000001 Serial number:
Coding: 0000018
Shop #: WSC 41776 001 1048576
VCID: 295904A98012A656EC9-807C
Subsystem 1 - Part No: 4F0 941 329 D
Component: AFS-Modul links H01 0010
Subsystem 2 - Part No: 4F0 941 329 D
Component: AFS-Modul rechtsH02 0010
1 Fault Found:
02628 - Sensor for Swivel Module Position; Right
008 - Implausible Signal - Intermittent
Freeze Frame:
Fault Status: 00101000
Fault Priority: 2
Fault Frequency: 2
Reset counter: 40
Mileage: 110168 km
Time Indication: 0
Date: 2015.02.17
Time: 18:20:07
Address 55: Xenon Range Labels: 4F0-910-357.lbl
Part No SW: 4F0 910 357 F HW: 4F0 907 357 F
Component: AFS 1 H01 0020
Revision: 00000001 Serial number:
Coding: 0000018
Shop #: WSC 41776 001 1048576
VCID: 295904A98012A656EC9-807C
Subsystem 1 - Part No: 4F0 941 329 D
Component: AFS-Modul links H01 0010
Subsystem 2 - Part No: 4F0 941 329 D
Component: AFS-Modul rechtsH02 0010
1 Fault Found:
02628 - Sensor for Swivel Module Position; Right
008 - Implausible Signal - Intermittent
Freeze Frame:
Fault Status: 00101000
Fault Priority: 2
Fault Frequency: 2
Reset counter: 40
Mileage: 110168 km
Time Indication: 0
Date: 2015.02.17
Time: 18:20:07
all you have to do is go into module 17 Instruments and recode it. Subtract 32 from your current value and save. On mine it was 0048203 and became 0016203 (my tire pressure sensors already are turned off).
This is the only thing, that will remove the warning light, pulling fuses or coding other modules did not work for me
Last edited by BASARAB; 12-01-2019 at 02:59 PM.
The following 2 users liked this post by BASARAB:
Aceler8 (04-10-2020),
Alberto Martinez Salinas (04-09-2020)
#14
AudiWorld Member
finally a solution
BASARAB = You are the man! After years of warning sounds and flashing icons on dash, this process worked perfect. This alone paid for my VagCom cable. Wish i could buy you a beer. Cheers
The following users liked this post:
BASARAB (04-10-2020)
#16
AudiWorld Member
If someone gets a code like this, or 02629 for the left head
all you have to do is go into module 17 Instruments and recode it. Subtract 32 from your current value and save. On mine it was 0048203 and became 0016203 (my tire pressure sensors already are turned off).
This is the only thing, that will remove the warning light, pulling fuses or coding other modules did not work for me
all you have to do is go into module 17 Instruments and recode it. Subtract 32 from your current value and save. On mine it was 0048203 and became 0016203 (my tire pressure sensors already are turned off).
This is the only thing, that will remove the warning light, pulling fuses or coding other modules did not work for me
0048203 - 32 = 0048171
So if i put in 0048171 and press "do it" the value will change to "0016203" ?
#17
AudiWorld Member
its 00??XXX so 48-32=16
00 does not change
xxx does not chang
0016203
Wow ...that's smart... Good job!!!
#18
Hi BASARAB, thanks for the info. I tried this and subtracted 32 from 3153288 and entered 3121288 but was unsuccessful in extinguishing the adaptive headlamp error message. Any thoughts on where I may have gone wrong? Sincerely, Jay
#19
Looks like you have an A6. Your coding will be different vs D3 model
Last edited by BASARAB; 11-20-2020 at 07:24 PM.
#20
Would it work in VW Passat ?
If someone gets a code like this, or 02629 for the left headlight
all you have to do is go into module 17 Instruments and recode it. Subtract 32 from your current value and save. On mine it was 0048203 and became 0016203 (my tire pressure sensors already are turned off).
This is the only thing, that will remove the warning light, pulling fuses or coding other modules did not work for me
all you have to do is go into module 17 Instruments and recode it. Subtract 32 from your current value and save. On mine it was 0048203 and became 0016203 (my tire pressure sensors already are turned off).
This is the only thing, that will remove the warning light, pulling fuses or coding other modules did not work for me
Fault code is the same: 02629.
Please info ?
thanks.
Thread
Thread Starter
Forum
Replies
Last Post
xkahn
A4 Cabriolet (B6 Platform) Discussion
8
02-08-2018 10:43 AM
Pmpsch
Q7 MKII Discussion
14
12-06-2015 01:14 PM
hardipk5
Audi 90 / 80 / Coupe quattro / Cabriolet
17
11-24-2015 03:42 AM
DannyG123US
Audi 5000 / 200 / V8 Discussion
4
09-07-2015 05:53 PM