Go Back   AudiWorld Forums > Audi Models > Audi A6 / S6 / RS 6 > A6 / S6 (C5 Platform) Discussion
Sign in using an external account
Register Forgot Password?


A6 / S6 (C5 Platform) Discussion Discussion forum for the C5 Audi A6 and S6 produced from 1998-2004

Welcome to AudiWorld Forums!
Welcome to AudiWorld.com.

You are currently viewing our forums as a guest, which gives you limited access to view most discussions and access our other features. By joining our community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is fast, simple and absolutely free so please, join the AudiWorld Forums community today!


Reply
 
 
 
 
LinkBack Thread Tools Search this Thread Display Modes
Old 02-17-2009, 09:13 AM   #1
Audiworld Junior Member
Account #: 117534
 
Join Date: Nov 2006
Posts: 18
Default Power Steering pump replacement - A6 3.0 - not too bad

Just replaced the power steering pump - actually not too bad. Looked around on this site for info before I replaced it and didn't see too much. There is no need to put the lock carrier into the service position. It took about 2 hrs and I was taking my time. The story starts out with the typical steering whining noise a few weeks back - I didn't attend to it right away (lesson learned), and once I did I realized that the pump intake hose was not fitting tightly anymore. So an air leak situation exists which of course produced the cavitation, bubbles in the reservoir, etc. Once I got around to replacing the hose though, the damage was pretty much done. I ordered a rebuilt ZF pump thru germanautoparts, which, by the way was the only supplier I could find, besides the stealer. As far as replacement, you'll need a 7/8" open end wrench to get on the serpentine belt tensioner, then push it down. While pushing it done, take the belt off of the pump pulley, and I used a bungee cord to keep tension on the rest of the belt so it wouldn't fall off, thereby creating a lot of extra work. Once you get the belt off and loosened the three pulley bolts (and siphoned off the fluid from the reservoir), it's just three 6mm hex bolts that hold the pump carrier onto the block. Relatively easy to access them and get them out. Disconnet the input hose and the high pressure banjo fitting. I placed rags underneath both so not to get fluid on the belt. I also used a flexible magnet to grab the bolt as I made the final turns to reduce the risk of falling down to the engine pan. Just be careful of the vacuum lines nearby when you lift the pump out. It really was that straightforward. Make sure to prime the new pump before you put it in. I reinstalled the plastic shipping seals on both the inlet and outlet fittings once I primed it, and left them on until I had the pump installed. That helped to keep the fluid inside. Remember to follow the standard Bentley bleeding procedure aftewards and you should be good to go.
Jim
__________________
2003 A6 Avant (3.0l)
bighands is offline   Reply With Quote
Old 02-17-2009, 10:03 AM   #2
AudiWorld Super User
Account #: 44417
 
SloopJohnB@mac.com's Avatar
 
Join Date: Oct 2002
Posts: 5,417
Default Mo bettah than gear-driven pump on 4.2 engines....

SloopJohnB@mac.com is online now   Reply With Quote
Old 02-17-2009, 04:17 PM   #3
AudiWorld Member
Account #: 88164
 
Join Date: Feb 2005
Posts: 118
Default Well done

Did you take any pics while you were working on this job?
Truewit is offline   Reply With Quote
Old 02-17-2009, 06:34 PM   #4
Audiworld Junior Member
Account #: 117534
 
Join Date: Nov 2006
Posts: 18
Default Re: Well done

I did not. Was too excited to get my steering back to think about it!
__________________
2003 A6 Avant (3.0l)
bighands is offline   Reply With Quote
Old 11-24-2011, 09:06 AM   #5
Audiworld Junior Member
Account #: 158771
 
Join Date: Feb 2009
Posts: 37
Default

How do you prime the pump?
Orangecounty is offline   Reply With Quote
Old 11-24-2011, 09:06 AM
AudiWorld
Audi R8




Paid Advertisement
 
 
 
Reply

Tags
2002, 30, 30l, a6, allroad, audi, belt, change, hose, power, pump, replace, replacement, serpentine, steering


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -8. The time now is 12:28 PM.


Copyright 2014 AudiWorld.com Audi Enthusiast Community

Personal Contacts

SEO by vBSEO ©2011, Crawlability, Inc.