Holy @##$#$$! No FOB upon return to Airport from Holiday!!! >
01-01-2009, 05:40 PM
#1
AudiWorld Senior Member
Thread Starter
Holy @##$#$$! No FOB upon return to Airport from Holiday!!! >
Arrived home from Holiday with relatives! Guess what! DOH!!! Key FOB was not with me! Taxi was expensive to go get the other one from my house .... found out the spare one needs to be programmed too! Luckily my sister found the FOB under neath the Guest bed .... i blame it on her cats!!! ahahahaha Any way can I program the spare with VAGCOM......I can't find the link to the programming instructions by searching the archives ....any help would be appreciated ....thanks in advance ......lessons learned the hard way 
01-01-2009, 06:22 PM
#2
Here you go --->>>
<b>Remote Matching</b>
For this procedure, you must have
1) VAG COM
2) A laser cut key (just one is "needed")
3) Up to 4 compatible remotes to program
Procedure for matching remote controls to most Audi vehicles:
Under "Select Control Module"
"Select"
"46 - Cent. Conv." or "35 - Cent. Locking" (depending on year and make/model)
"Adaptation - 10"
First enter channel "00" as this will set all settings back to factory.
Enter channel "01" (Again "21 depending on make/model).
"Read"
This is supposed to display the number of currently stored remotes in "Stored Value". But a lot of people actually get 0.
According to ross-tech, this is what you must do next which is the part that messes everyone up - "Enter your total number of keys up to a maximum of 4 (including any existing keys) in 'New Value.'" Do not do that. Instead, for your first remote just put in a one.
"Test"
Verify that the number in "Test Value" is the one you entered.
Now this is another place that ross-tech tells you to do something that doesn't work... They tell you to hit the "Save" button, but what are you saving? Absolutely nothing!! Notice up at the top it should say something along the lines of "Key Adaptation." If it says this, you have 15 seconds to push the unlock button on your remote (hold for two seconds) or until it says "Key learned." NOW is where you hit save.
"Save"
It should now ask if you are sure you want to save. Of course you do.
The procedure also says right about now that the car will give you some kind of sign that the remote was learned such as a (lights flash, horn beep, etc.) but as long as the VAGCOM said "learned" it will be fine.
But for remote number two pretty much follow the same above for number one.
For this procedure, you must have
1) VAG COM
2) A laser cut key (just one is "needed")
3) Up to 4 compatible remotes to program
Procedure for matching remote controls to most Audi vehicles:
Under "Select Control Module"
"Select"
"46 - Cent. Conv." or "35 - Cent. Locking" (depending on year and make/model)
"Adaptation - 10"
First enter channel "00" as this will set all settings back to factory.
Enter channel "01" (Again "21 depending on make/model).
"Read"
This is supposed to display the number of currently stored remotes in "Stored Value". But a lot of people actually get 0.
According to ross-tech, this is what you must do next which is the part that messes everyone up - "Enter your total number of keys up to a maximum of 4 (including any existing keys) in 'New Value.'" Do not do that. Instead, for your first remote just put in a one.
"Test"
Verify that the number in "Test Value" is the one you entered.
Now this is another place that ross-tech tells you to do something that doesn't work... They tell you to hit the "Save" button, but what are you saving? Absolutely nothing!! Notice up at the top it should say something along the lines of "Key Adaptation." If it says this, you have 15 seconds to push the unlock button on your remote (hold for two seconds) or until it says "Key learned." NOW is where you hit save.
"Save"
It should now ask if you are sure you want to save. Of course you do.
The procedure also says right about now that the car will give you some kind of sign that the remote was learned such as a (lights flash, horn beep, etc.) but as long as the VAGCOM said "learned" it will be fine.
But for remote number two pretty much follow the same above for number one.
01-01-2009, 10:02 PM
#4
AudiWorld Senior Member
Thread Starter
Thank you!!! Great Info! I'll try this week! I love this board! Like always>
the info here is so helpful!!! Makes me want to rebuild an engine or something ...ahaha!!!
Trending Topics
Thread
Thread Starter
Forum
Replies
Last Post
mksap11
Q7 MK 1 Discussion
25
01-12-2018 04:18 PM
shwndh
A4 (B6 Platform) Discussion
2
02-26-2008 04:30 PM